例题:角锥喇叭建模尺寸 5.16in0.315in Air box Horn Antenna Horn一、创建工程 第一步:打开HFSS并保存新工程 打开HFSS 软件后,自动创建一个新工程:Project1。 由主菜单选File\Save ,保存在指定的文件夹内,命名为horn。 一、创建工程 第二步:插入HFSS设计 由主菜单选Project\ Insert HFSS Design,则一个新项目 自动加入到工程树中,默认名HFSSModel1。同时,在工程 树的右侧出现绘图窗口。 在工程树中选择HFSSModel1,点右键,选择Rename项, 将设计命名为HornModel。 一、创建工程 第三步:选择求解类型 由主菜单选HFSS\Solution Type ,在弹出对话窗选择 Driven Model 一、创建工程第四步:设置单位: 由主菜单选3D Modeler\Units ,在Set Model Units 对话 框中选中in Boxicon followingvalues -0.2, -0.45, 0.4,0.9, 0.315 dx,dy, dz,respectively otherwords, itscenter. 二、创建模型 HornType Base namefield. Material assigned vacuumandchoose Color yourpreference. Click Ok. 二、创建模型 base2D Rectangle hornantenna, draw connectTwo rectangles, connectthem 3Dfunnel. Place firstrectangle 3Dantenna base. Draw>Rectangle. Now move onecorner antennabase, oppositecorner antennabase clickagain. rectanglewindow open.Type funnel_base. Assign material vacuum.Choose Color yourpreference. Click Ok. Note rectangleshould match those antennabase. 二、创建模型 HornAperture Next, draw 2Drectangle horn.Click Rectangle icon Draw>Rectangle.Type followingvalues: 0.972, 1.325, 5.475 followingvalues: -1.944 dy,respectively. Type horn_top namefield. Assign material vacuum.Choose youpreference. Click Ok. 二、创建模型 Connecting2D Objects FunnelNow you can connect 2Dobjects makeup 3D,funnel-shaped object. Choose funnel_basefrom Modeltree holdingdown Ctrlkey. Go 3DModeler> Surface >connect. Name funnel.Note unitingother objects can edited.When connecting 2D objects, example,you can edit original2D objects, youcan editdirectly 3Dobject connectcommand. 二、创建模型 hornbase FunnelAlthough strictlynecessary, you two3D objects-the horn base createone 3D horn antenna structure. problemsimpler minimum.Choose base funnelfrom 3Dobjects. 3DModeler> Boolean>Unite. clinkOk. 二、创建模型 3DAir Box Around HornAntenna hornantenna, you need bounded“box” air.Click Box icon Draw>Box. Type followingvalues: -1.5, -2, dx,dy, dz,respectively. Type AirBox namefield, vacuumis assignedmaterial chooseColor yourpreference. Click Ok. 三、设置边界条件和激励源 Choose assignPerfect Allfaces hornshould chosenexcept Boundariesright click Assign< Perfect PerfE_horn_sides.三、设置边界条件和激励源 Assign radiation boundary airbox. Choose airbox Boundariesright-click AssignSetup1> Add sweep. Set following:Sweep Type fast,Frequency Setup type Linearcount, Start GHz,Stop 12GHz 100.四、设置求解项并分析 Makesure validatecheck. HFSSCreate Report. Accept Defaultvalues clickingOk. Make sure followingvalues AddTrace, clickDone. 五、察看结果图 Creating Farfield Plot farfield plot 3-Dplot far-fieldradiation pattern. Right-click Radiation, chooseInsert Far Field Set> Infinite Sphere… 五、察看结果图 Creating Farfield Plot farfield plot 3-Dplot far-fieldradiation pattern. Right-click Results, chooseCreate report. Set Report Type FarFields Displaytype 3DPolar. 五、察看结果图 Creating Farfield Plot farfield plot 3-Dplot far-fieldradiation pattern. When Traces Window open, leave set.Make sure LastAdaptive Solutionfield GeometryisInfiniteSphere1. Under Sweep tab, make sure Phi primarysweep secondarysweep allvalues checked.Make sure rE pickedunder Category, rE Total under quantity noneunder function. Click Add Trace, Done.求职应注意的礼仪 最优雅的礼仪修养是体现自然以一种修养面对两种结果 仍然感谢这次机会,因为被拒绝是面试后的两种结果之一。 被拒绝是招聘单位对我们综合考虑的结果,因为我们最关心的是自己什么地方与用人要求不一致,而 不仅仅是面试中的表现。 把走进工作岗位当作职业生涯的重要的第一步,认真思考如何为以后的发展开好头。 Thank you
盘锥形天线是一种超短波天线。
其结构如图6所示,顶部为一圆盘(即辐射体),由同轴线的心线馈电,下面为一圆锥,接同轴线的外导体。圆锥的作用与无限大的地面相似,改变圆锥的倾斜角度,就能改变天线的最大辐射方向。它有极宽的频带
免责声明:本文系网络转载或改编,未找到原创作者,版权归原作者所有。如涉及版权,请联系删