产品
说明：
1、交换机模块是未插在机器上边的，实施前检查模块数量并插入前12port。
2、没有端口扩容的license的情况下，每台交换机默认12port激活。
3、端口扩容license每个可以激活12port，48port全激活的交换机需要3个license。
初始化:
Abort Auto Provisioning and continue with normal setup ?(yes/no)[n]: y
//取消自动配置并继续正常设置?
---- System Admin Account Setup ---- //系统管理帐户设置
Do you want to enforce secure password standard (yes/no) [y]: y
//您想要强制执行安全密码标准吗
Enter the password for "admin": P@ssw0rd
Confirm the password for "admin": P@ssw0rd
---- Basic System Configuration Dialog ---- //基本系统配置对话框
This setup utility will guide you through the basic configuration of the system. Setup configures only enough connectivity for management of the system.
//这个设置实用程序将指导您完成系统的基本配置。设置仅配置系统管理所需的连接性。
Please register Cisco MDS 9000 Family devices promptly with your supplier. Failure to register may affect response times for initial service calls. MDS devices must be registered to receive entitled support services.
//请立即向您的供应商注册Cisco MDS 9000系列设备。注册失败可能会影响初始服务调用的响应时间。MDS设备必须注册才能获得相应的支持服务。
Press Enter at anytime to skip a dialog. Use ctrl-c at anytime to skip the remaining dialogs.
//按回车在任何时候跳过一个对话框。在任何时候使用ctrl-c来跳过剩下的对话框。
Would you like to enter the basic configuration dialog (yes/no): y
//您要输入基本配置对话框吗
Create another login account (yes/no) [n]: //创建另一个登录帐户
Configure read-only SNMP community string (yes/no) [n]: //配置只读SNMP共同体字符串
Configure read-write SNMP community string (yes/no) [n]: //配置读写SNMP共同体字符串
Enter the switch name : MDS9148-1 //配置交换机名称
Continue with Out-of-band (mgmt0) management configuration? (yes/no) [y]: y
//继续带外(mgmt0)管理配置?
Mgmt0 IPv4 address : 192.168.10.12
Mgmt0 IPv4 netmask : 255.255.255.0
Configure the default gateway? (yes/no) [y]: //配置网关
Mgmt0 IPv4 gateway :192.168.10.1
Configure advanced IP options? (yes/no) [n]: //配置高级IP选项?
Enable the ssh service? (yes/no) [y]: //启用SSH服务
Type of ssh key you would like to generate (dsa/rsa) [rsa]: //希望生成的ssh密钥的类型
Number of rsa key bits <1024-2048> [1024]: // rsa密钥位的数目
Enable the telnet service? (yes/no) [n]: y //启用telnet服务
Configure congestion/no_credit drop for fc interfaces? (yes/no)[y]: no
//为fc接口配置拥塞/无信用下降?
Enable the http-server? (yes/no) [y]: //启用http服务器
Configure clock? (yes/no) [n]: //配置时钟
Configure timezone? (yes/no) [n]: //配置时区
Configure summertime? (yes/no) [n]: //配置夏季时间
Configure the ntp server? (yes/no) [n]: //配置NTP服务器
Configure default switchport interface state (shut/noshut) [shut]:
//配置默认的交换机接口状态
Configure default switchport trunk mode (on/off/auto) [on]: off
//配置默认的交换机端口中继模式
Configure default switchport port mode F (yes/no) [n]: //配置默认的switchport端口模式F
Configure default zone policy (permit/deny) [deny]: //配置默认区域策略
Enable full zoneset distribution? (yes/no) [n]: //启用完整的zoneset分发?
Configure default zone mode (basic/enhanced) [basic]: //配置默认区域模式
The following configuration will be applied: //将应用以下配置
password strength-check
switchname MDS9148-1
interface mgmt0
ip address 192.168.10.12 255.255.255.0
gatway 192.168.10.1
no shutdown
ssh key rsa 1024 force
feature ssh
feature telnet
feature http-server
system default switchport shutdown
system default switchport trunk mode off
no system default zone default-zone permit
no system default zone distribute full
no system default zone mode enhanced
Would you like to edit the configuration? (yes/no) [n]: //您想要编辑配置吗?
Use this configuration and save it? (yes/no) [y]: //使用此配置并保存它?
[########################################] 100%
Copy complete.
配置:
创建vsan
config t
vsan database
vsan 100 name vsan100
end
激活端口
config t
interface fc1/1-48
no shut
end
添加端口到vsan
config t
vsan database
vsan 100 interface fc1/1-48
end
查看端口所属vsan
show interface brief
查看光口wwn
show flogi database
设置别名
config t
device-alias database
device-alias name UNITY_SPA_P4 pwwn 50:06:01:62:49:e0:2d:3c
device-alias name UNITY_SPB_P4 pwwn 50:06:01:6a:49:e0:2d:3c
device-alias name R840_DB_02_slot3_P0 pwwn 10:00:00:10:9b:5a:68:55
device-alias name R840_DB_01_slot3_P0 pwwn 10:00:00:10:9b:5a:66:7f
device-alias commit
end
设置zone
config t
zone name R840_DB_02_slot3_P0_UNITY_SPA_P4 vsan 100
member device-alias R840_DB_02_slot3_P0
member device-alias UNITY_SPA_P4
exit
zone name R840_DB_02_slot3_P0_UNITY_SPB_P4 vsan 100
member device-alias R840_DB_02_slot3_P0
member device-alias UNITY_SPB_P4
exit
zone name R840_DB_01_slot3_P0_UNITY_SPA_P4 vsan 100
member device-alias R840_DB_01_slot3_P0
member device-alias UNITY_SPA_P4
exit
zone name R840_DB_01_slot3_P0_UNITY_SPB_P4 vsan 100
member device-alias R840_DB_01_slot3_P0
member device-alias UNITY_SPB_P4
exit
end
设置zoneset
config t
zoneset name zoneset1 vsan 100
member R840_DB_02_slot3_P0_UNITY_SPA_P4
member R840_DB_02_slot3_P0_UNITY_SPB_P4
member R840_DB_01_slot3_P0_UNITY_SPA_P4
member R840_DB_01_slot3_P0_UNITY_SPB_P4
end
激活zoneset
config t
zoneset activate name zoneset1 vsan 100
保存
copy run start
查看:
查看vsan
#show vsan
vsan 1 information
name:VSAN0001 state:active
interoperability mode:default
loadbalancing:src-id/dst-id/oxid
operational state:down 注意：此时为down的状态
vsan 100 information
name:vsan100 state:active
interoperability mode:default
loadbalancing:src-id/dst-id/oxid
operational state:down 注意：此时为down的状态
vsan 4079:evfp_isolated_vsan
vsan 4094:isolated_vsan
查看vsan端口信息
show vsan 100 membership
查看交换机所有端口信息
#show interface brief
MDS9148-2# show interface brief
-------------------------------------------------------------------------------
Interface Vsan Admin Admin Status SFP Oper Oper Port
Mode Trunk Mode Speed Channel
Mode (Gbps)
-------------------------------------------------------------------------------
fc1/1 1 auto off up swl F 16 --
……
fc1/7 1 auto off notConnected swl -- -- --
……
fc1/13 1 auto off sfpAbsent -- -- -- --
状态：up为连接，notConnected未连接，sfpAbsent没许可。
# show flogi database
-------------------------------------------------------------------------------
INTERFACE VSAN FCID PORT NAME NODE NAME
-------------------------------------------------------------------------------
fc1/1 1 0x890000 50:06:01:63:49:e0:2d:54 50:06:01:60:c9:e0:2d:54
fc1/2 1 0x890100 50:06:01:6b:49:e0:2d:54 50:06:01:60:c9:e0:2d:54
显示当前配置
show run
显示当前配置的ZONE的信息
show zone
显示当前配置的ZONESET的信息
show zoneset
显示端口fc1/1信息
show interface fc1/1
显示当前活动的ZONE信息
show zone activate
显示当前活动的ZONESET信息
show zoneset activate
查看连接的HBA卡的WWN号
show flogi database detail
查看注册的WWN号
# show fcs database
查询连接的hba卡的wwn的信息
# show flogi database
查看交换机状态
# show environment
查看交换机整体信息
# show hardware
保存当前配置
copy run start
显示指定License
switch# show license fcports.lic
显示全部Licenses
switch# show license all
显示SN
switch# show license hostid
License hostid:VDH=4C0AF664
其他命令
更改交换机名称
config t
switchname XXX
更改交换机管理ip
config t
interface mgmt 0
ip address XXXXX
从zoneset中移除zone
# conf t
# zoneset name zoneset1 vsan 100
# no member qa 从zoneset移除名为qa的zone
移除zone的member
# conf t
# zone name qa vsan 100
# no member interface fc1/1
# no member interface fc1/10
删除zone
# no zone name qa vsan 100
别名重命名
switch(config-device-alias-db)# device-alias rename Device1 Device2
指定端口为E工作模式
switch(config)# interface fc1/1
switch(config-if)# switchport mode e
安装与清除license
switch# install license bootflash:license-file
switch# clear license license-file
switch# clear license all
下载配置文件
switch# copy <scheme>://<url> system:running-config
switch# copy tftp://172.16.10.1/237.img bootflash: 237.img
收集日志在#模式下收集
term len 0（不需要手动敲空格）
show tech-support details
show logging onboard error-stats
更改日期
例：
MDS9148S-1# clock set 11:55:00 22 November 2019
清除配置
write erase
执行完命令后，交换机关机，再开机，此时可使用串口线重新初始化。
重启
reload
This command will reboot the system。(y/n)? y
升级
使用show version命令查看
# show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html
Copyright (c) 2002-2017, Cisco Systems, Inc. All rights reserved.The copyrights to certain works contained herein are owned byother third parties and are used and distributed under license.Some parts of this software are covered under the GNU Public License. A copy of the license is available athttp://www.gnu.org/licenses/gpl.html.
Software
BIOS: version 2.1.17
loader: version N/A
kickstart: version 6.2(19)
system: version 6.2(19)
BIOS compile time: 01/08/14
kickstart image file is: bootflash:///m9100-s5ek9-kickstart-mz.6.2.19.bin
kickstart compile time: 1/30/2017 23:00:00 [03/10/2017 05:18:49]
system image file is: bootflash:///m9100-s5ek9-mz.6.2.19.bin
system compile time: 1/30/2017 23:00:00 [03/10/2017 08:12:56]
Hardware
cisco MDS 9148S 16G 48 FC (1 Slot) Chassis ("2/4/8/16 Gbps FC/Supervisor")
Motorola, e500v2, core 0 with 4155776 kB of memory.
Processor Board ID JAE22450LU8
Device name: MDS9148S-1
bootflash: 4018896 kB
Kernel uptime is 1 day(s), 4 hour(s), 43 minute(s), 7 second(s)
Last reset
Reason: Unknown
System version: 6.2(19)
Service:
plugin
Core Plugin
使用TFTP软件上传软件包到bootflash
# copy tftp://<server IP address>/<filename in TFTP> bootflash:<image filename>
例如：
copy ftp://192.168.10.111/m9100-s5ek9-mz.6.2.27.bin bootflash:m9100-s5ek9-mz.6.2.27.bin
copy ftp://192.168.10.111/m9100-s5ek9-kickstart-mz.6.2.27.bin bootflash:m9100-s5ek9-kickstart-mz.6.2.27.bin
说明：需要将下载好的zip文件解压放在FTP目录下，共两个文件，copy命令需要执行两次上传。
查看上传好的文件
#dir bootflash
升级前检查
1）升级前检查是否有特性不兼容问题
Switch# show incompatibility-all system bootflash：文件名
2）升级前检查硬件冲突
Switch# show install all impact kickstart bootflash:m9500-sf2ek9-kickstart-mz.5.0.8.bin
system bootflash:m9500-sf2ek9-mz.5.0.8.bin
3）确认业务已经暂停
4）使用show sprom backplane 1确认要升级的交换机序列号
5）使用copy running-config startup-config保存当前配置，以防交换机重启后配置丢失
6）保存当前配置到本地
#copy startup-config tftp://<server IP address>/<startup-config_switchname_date>
7）收集当前日志信息
show tech-support details
8）执行show version确认当前硬件型号和软件版本
9）执行show module检查交换机组件状态
10）执行show hardware检查交换机是否已经boot up
11）执行show flogi database检查并记录flogi信息和数量
12）执行show system health statistics检查是否都是running
13）执行show vsan检查vsan1是否是active
执行升级命令
# install all system bootflash:<system image name> kickstart bootflash:<kickstart image name>
例如
#install all system bootflash:m9100-s5ek9-mz.6.2.27.bin kickstart bootflash:m9100-s5ek9-kickstart-mz.6.2.27.bin
Do you want to continue with the installation (y/n)? [n] y
确认升级
升级完成后
检查交换机组件状态
Show module
安装许可
说明：
1）Cisco交换机端口扩容license每个可以激活12port，48port全激活的交换机需要3个license。
2）Cisco交换机激活官方网站提供链接，但需要合作伙伴权限，否则只能拨打400客服电话激活。
3）Cisco交换机激活只需要提供交换机SN和激活码PAK。
4） Cisco交换机许可以lic文件形式通过邮件附件下发给工程师。
步骤：
1.上班激活文件
#copy ftp://192.168.10.11/ 20191008145312690.lic bootflash: 20191008145312690.lic
2.查看激活文件
#dir bootflash
3.安装激活文件
#install license bootflash: 20191008145312690.lic
4. 检查已安装的许可证
#show license usage
#show license brief
收集日志
show tech-support details
show logging [logfile|nvram] 查看交换机日志信息，可以查看日志文件内容，或者nvram里面的日志信息。
155-2731-8020
