当前位置：服务支持 > 软件文章 > Matlab Hardware：MathWorks MATLAB硬件团队

Matlab Hardware：MathWorks MATLAB硬件团队

阅读数 4

Submitted

MATLAB Support Package for Arduino Hardware

Acquire inputs and send outputs on Arduino boards

10 days ago | 1908 downloads |

Submitted

MATLAB Support Package for Raspberry Pi Hardware

Acquire sensor and image data from your Raspberry Pi.

10 days ago | 396 downloads |

Answered

Arduino Nano 33 BLE to MATLAB

Hi EB,

Kindly note that the support for Nano33BLE will be available from R2021a onward through the MATLAB Support Package for A...

1 month ago | 1

Answered

Failed to read i2c device's register with MATLAB Support Package for Raspberry Pi Hardware

Hi FlyWing,

Can you please perform following steps and see in all three cases you are getting same values, if not then please c...

3 months ago | 0

Answered

Why does disableI2C() stalls the Raspberry Pi?

This is due to the upstream Linux issue for BCM 2835 based devices. This issue has been reported in following Raspberry Pi forum...

6 months ago | 0

| accepted

Question

Why does disableI2C() stalls the Raspberry Pi?

I have a Raspberry Pi 3B+ with MathWorks customized Raspbian image for R2020b. When I execute following commands, I see an erro...

6 months ago | 1 answer | 0

1answer

Submitted

MATLAB Support Package for Ryze Tello Drones

MATLAB® Support Package for Tello Drones provides interfaces to control a DJI Ryze Tello drone from MATLAB.

6 months ago | 62 downloads |

Submitted

MATLAB Support Package for Parrot Drones

Control Parrot drones from MATLAB and acquire sensor data

6 months ago | 62 downloads |

Submitted

MATLAB Support Package for BeagleBone Black Hardware

Interact with BeagleBone Black from MATLAB

6 months ago | 24 downloads |

Answered

does it is possible to live stream video in matlab with H.264 codec

Hi Haris,

MATLAB will be supporting H.264 encoded RTSP streams for IP Cameras through MATLAB Support Package for IPCameras in t...

7 months ago | 1

Answered

Read data from Arduino Nano 33 IoT IMU sensor

Hi Matthias,

I see that you are using a correct subset of I2C APIs documented to read out the sensor register...

11 months ago | 0

| accepted

Submitted

MATLAB Support Package for LEGO MINDSTORMS EV3 Hardware

Acquire sensor data and control outputs on LEGO MINDSTORMS EV3

1 year ago | 64 downloads |

Answered

Can I connect the VCC and GND pins of the NeoPixel addon directly to the VCC and GND pins of Arduino?

No, as the NeoPixel requires high current which cannot be supplied by the Arduino board. For power supply specifications of Ne...

1 year ago | 1

Question

Can I connect the VCC and GND pins of the NeoPixel addon directly to the VCC and GND pins of Arduino?

1 year ago | 1 answer | 0

1answer

Answered

In the Capacitive Sensor addon, can I use an analog pin on the Arduino board as the ‘sendPin’ or ‘receivePin’?

This depends on the Arduino board. In some boards like the Leonardo, you cannot use an analog pin as a digital pin. To check if ...

1 year ago | 0

Question

In the Capacitive Sensor addon, can I use an analog pin on the Arduino board as the ‘sendPin’ or ‘receivePin’?

1 year ago | 1 answer | 0

1answer

Answered

How can I find the state of the SA0 pin and the DeviceType for LSM303 or L3G addons when it cannot be auto detected by MATLAB Arduino support package?

For details on the SA0 pin, see section ‘I2C Communication’ https://www.pololu.com/product/2127.

The ‘Device type’ of the de...

1 year ago | 0

| accepted

Question

How can I find the state of the SA0 pin and the DeviceType for LSM303 or L3G addons when it cannot be auto detected by MATLAB Arduino support package?

How can I find the state of the SA0 pin and the DeviceType for LSM303 or L3G addons when it cannot be auto detected by MATLAB Ar...

1 year ago | 1 answer | 0

1answer

Submitted

1-Wire Add-On Library for Arduino

Communicate with 1-Wire devices connected to Arduino hardware in MATLAB.

1 year ago | 11 downloads |